Are riser pads necessary?

Sometimes you’re going to need riser pads. Installing riser pads will give you that extra clearance between the wheels and the skateboard deck to keep you safe when leaning into turns, or pivoting with loose trucks. Skating with risers greatly reduces the risk of wheel-bite.

Can shock pads be used as risers?

It doesn’t take much of rise to feel a difference, so keep it under 3/8 of an inch. Rubber shock pads achieve the same purpose as riser pads do, but they add the extra benefits of a cushioned ride.

What do angled riser pads do?

Angled or wedge risers do not only raise your deck, but also fixes them at an angle from your deck. You can install them so they are angled away from the center, or towards the center. The wedge riser pads change the angle of the kingpin and the pivot point.

Do pros use riser pads?

Do you use any riser pads? No riser pads.

Do riser pads give more pop?

Shortboarders may also use them to prevent wheel bite after landing a skate trick, thus prolonging the life of their board. They also have the added bonus of giving your board extra pop, since they add more distance between the tail and the ground.

Are risers and shock pads the same?

The difference between riser pads and shock pads First, they have slightly different purposes. Riser pads are designed to increase the height of your board in order to avoid wheel bite, and shock pads are designed to absorb shock to make for a smoother ride.

What size riser pads should I get?

If you plan on setting up your skateboard with risers you will need some longer bolts. Risers are usually recommended for larger wheels 55mm and above, and while not necessary for smaller skate wheels, 1/8″ shock pads can always be used to help reduce vibration and stress cracks to your board.

What size riser should I get?

For most physically fit adults with a draw length between 26 and 31 inches I would suggest opting for a 25-inch riser paired with short limbs for draw lengths of 26 to 28 inches, medium limbs for draw lengths of 28 to 30.5 inches, or long limbs for draw lengths of 30.5 inches and over.

Where to put riser pads on a skateboard?

If you want to increase your turn capability, install the angled riser so that the thickest part is closer to the centre of the deck.

How do you lay decking on a riser?

All you now need to do is to lay your decking boards one by one and attach them to the timber frame. There are two possible ways to fasten down your boards: or clips. Please note that composite decking is almost always secured using clips while screws are the fixing of choice for timber decking.

What’s the best way to lay a deck on the ground?

If you’re laying your deck straight onto the ground, cover the area with a layer of weed control fabric. Then add 40 mm to 50 mm of gravel on top. The other method is to create concrete pads for the deck to sit on top of. This will reduce the likelihood of moisture seeping into the frame and causing damage.

Can a riser be fixed to the ground?

As they are equipped with a base, the risers (also known as pedestals) can be fixed to the ground if required or else left as a floating installation. The main advantage of adjustable risers is that they enable you to easily adjust the level of your deck.

All you now need to do is to lay your decking boards one by one and attach them to the timber frame. There are two possible ways to fasten down your boards: or clips. Please note that composite decking is almost always secured using clips while screws are the fixing of choice for timber decking.

If you want to increase your turn capability, install the angled riser so that the thickest part is closer to the centre of the deck.

Can you use shock pads on a riser pad?

In shock pads, losing a bit of speed is a natural consequence of shock absorption. Most riser pads won’t really affect speed unless they are very tall and result in a much higher center of gravity. Riser pads and shock pads share a lot of obvious common ground, which is why you can find them stocked side by side in most skate shops.

What’s the best way to fasten a deck?

There are two possible ways to fasten down your boards: or clips. Please note that composite decking is almost always secured using clips while screws are the fixing of choice for timber decking. It is important to pre-drill holes in your decking boards boards.